Topseal Roofing Trims
Roof Edge Detailing Made Quick, Easy and Simple
A complete range of GRP preformed roof trims and sections suitable for all liquid applied polymeric and single membrane systems. Our unique high adhesion finish gives excellent adhesion to most liquid applied systems without the need for priming. (Tested with both rigid and flexible polyester, polyurethane, acrylic and alkyd systems.) Suitable for flat roofing, pitched roofing, cladding, domestic and industrial applications.
   
  • Consistent Weight and Thickness
  • Three Metre Lengths
  • Choice of Laminate Weight and Thickness
  • Excellent Finished Appearance
  • Easily Jointed
  • Facilitates Roof Void Ventilation
  • Unique High Adhesion Finish
  • Fire Retardant (BS 476 Part 3)
  • Highly Flexible
  • U.V. Stabilised and Pre-Pigmented
  

 

Click a Section Picture to view a larger version and in situ drawing. PDF drawings are also available for download in ZIP format to assist architects.

  
 

 
 
Topseal Roofing Trims

 
Section
Code
 Description
Weight
Application
A170

Drip Fascia

170mm girth

65mm deep fascia

 S Fitted to roof edge for drainage into gutter. Used on edge detailing which requires a smaller drip trim.
A200

Drip Fascia

200mm girth

90mm deep fascia



S

 

 Fitted to roof edge for drainage into gutter. All edge detailing where drainage is required.
A250

Drip Fascia

250mm girth

140mm deep fascia

 S Roof edge detail to cover insulation. Deep fascia to allow gutter penetration.
B230

Raised edge trim

Check kerb 230mm girth

105mm fascia depth



S

 

 Flat roof edge detail to prevent water run off.
B260

Raised edge trim

260mm girth

125mm fascia depth


S

 

 Roof edge detail. Compatible with Universal external covers.
C100

Simulated lead wall cover flashing

100mm vertical cover

35mm wall penetration

 S Replaces traditional lead flashing. With integral moisture trap return, self secures into brickwork
C100 std

Simulated lead wall cover flashing

100mm vertical cover

35mm wall penetration

 

 S As above but without integral moisture trap.
ER35/40

Top hat section

 S For use with simulated lead or copper sheathing systems to give the appearance of a rolled joint.
D260

Wall fillet

260mm girth

90mm & 110mm flanges

120/140mm upstand height


S

 

 For use against abutting walls. Gutter lining. Provides expansion jointed and cross roof ventilation.
B300

Raised Edge Trim

300 / 330mm girth

175mm Fascia Depth


S

 
Roof edge detail compatible with external covers.
E280

Expansion Joint

300mm girth

100mm flanges

50mm height

S

 

 Expansion joint for use on large roof areas with rigid systems or to cover existing ex joints on refurb. May also be used to control roof drainage.
F300

Flat Flashing

Up to 1350mm wide

Rolls from 24m long

300mm standard width

 S Flat section for use as continuous flashing under slates at roof junction. Gutter lining.
G180

Expansion Joint

180mm girth

160mm wide

15mm height

 S Expansion joint for use on large roof areas. May also be used to control roof drainage.
 
 

 
 
Topseal Roofing Trims ( CORNERS )

 
Section
Code
 Description
Application
C1

Universal external corner.

Hot press moulded GRP pre formed corner.

 For use with Sections A200 and B260. Provides pre-formed RH and LH corners.
C2

Fillet to trim

RH and LH mouldings.

 For use at junction of flat roof and abutting wall. Compatible with sec. D260, A200, B260.
C3

Fillet corners

Internal and external.

Chimney corners. Compatible with D260 only.
C4

Universal internal corner.

 

 For use with A200 and B260.
C5

Expansion joint closure

 

 For use with E280 to seal end of expansion joint to roof deck.
 
 

 
 
Topseal Roofing Trims ( PITCHED ROOFING )

 
Section
Code
 Description
Application
CE300

Continuous eaves course

Colour slate grey. Non binding finish

 For use in place of first eaves slate course to provide initial lap.
 
 

All trims finished in light grey with outer high adhesion finish unless otherwise stated.
All sections cut to 3 metre length except F300 and CE300 which are available in min. 20 metre rolls.
S. Standard laminate weight. 450gm. per sq. metre (1.1mm thick)

 
 
Topseal Roofing Trims

 
Internal & External Angles`
AT175INT. 2.4m 175mm Girth Angle Trim Bonding Surface on Inside

AT175EX. 2.4m 175mm Girth Angle Trim. Bonding Surface on Outside
S500 Soffit Trim. 10" Fascia Soffit Trim. Used to encapsulate concrete deck edges.